Finite Element Numerical Simulation Research Articles

Wave‐to‐Wire Model and Output Performance Analysis of a Point Absorption Wave Energy Converter Based on Triboelectric Nanogenerator

Herein, a point absorption wave energy converter (WEC) model combined with a contact–separation mode triboelectric nanogenerator (PAW TENG) is proposed. The model considers the interaction between the hydrodynamic forces captured by a point absorption conversion device of wave energy and the electrostatic force of the TENG. According to the established harmonic oscillation model of the buoy, the buoy's hydrodynamic properties and power generation characteristics are studied using finite element simulation and numerical simulation calculations. The best matching resistor circuit for PAW TENG in regular waves is investigated and analyzed. The electrical characteristics of the PAW TENG in the irregular wave spectrum are also solved. This work will provide design ideas for the experimental design of a novel point absorption WEC.

Numerical simulation and experimental study on the compression performance of a double layer cross-lattice-core sandwich structure

Lattice sandwich structures are widely used in many engineering fields for their excellent mechanical properties, such as aerospace, transportation, construction and so on. In this paper, a new type of double layer cross-lattice-core sandwich structure is proposed. Firstly, based on the nonlinear finite element software ABAQUS, a finite element numerical simulation analysis is processed to the sandwich structure unite cell under flat compression. The deflection pattern, load-displacement curve and internal energy-displacement curve are obtained to discuss the compression performance of the unite cell with some specific geometric parameters, such as arm length ratio, clamped angle and thickness of the cross-lattice-core. It is found that the compression performance of the lattice sandwich structure with an arm length ratio of 1 and an included angle of 90° is optimal. The energy absorption effect decreases slightly with the increases of the arm length ratio increases, which will be greatly reduced when the core angle is lower than 90°. Then the unite cell model of the structure is prepared using 3D printing technology, and its compression performance is investigated by flat compression tests and verified in comparison with the numerical analysis results. Finally, the load-bearing property of the structure is further verified by compression analysis of a plate structure consisting of several unite cells. The results provide a reference for the design and engineering application of the structure.

Progressive Failure Mechanism of Shield Tunnel Face in Complex Urban Geological Environment

The construction of multiple tunnels across inland rivers has had a significant influence on the improvement of the transportation infrastructure. The technology for constructing tunnels is progressing towards the development of larger cross-sections, longer distances, and the ability to withstand high hydraulic pressure in complex hydrogeological conditions, including high-permeability strata. In order to ensure the face stability of shield tunnels under high hydraulic pressure that crosses a fault fracture zone, it is necessary to study the progressive failure mechanism of shield tunnel faces induced by high hydraulic pressure seepage. This paper employs finite element numerical simulation software to methodically examine the variation in the characteristics of the water seepage field, limiting support force, and face stability failure mode of shield tunnels passing through fault fracture zones with high hydraulic pressure under varying fault fracture width zones. The results show that the formation hydraulic gradient will progressively widen when the tunnel face is located within the undisturbed rock mass and is advanced towards the area of fault fracture. This will raise the likelihood of instability in the shield tunnel and progressively raise the limiting support force on the tunnel face. Moreover, as the tunnel face nears the region of fault fracture within the undisturbed rock mass, the damage range increases gradually. In addition, due to the increase in seepage force, the angle between the failure area and the horizontal plane becomes more and more gentle. On the contrary, as the tunnel’s face moves closer to the undisturbed rock mass from the region of the fault fracture, the damage range gradually decreases, and the dip angle between the damage area and the horizontal plane becomes steeper and steeper due to the decreasing seepage force in the process. The study findings presented in this work are highly significant, both theoretically and practically, for the design and management of safety.

Effects of jet grouting on adjacent ground through numerical modelling

When using jet grouting for soil stabilization, effects of the installation process, such as erosion or remolding of the surrounding soil, need to be evaluated. This could be particularly important for applications in challenging ground conditions and low initial ground stability. This study investigates such effects in soft marine clays (undrained shear strength of 20-30 kPa) using numerical finite element simulations for both flat and sloping terrains. Additionally, an analytical solution using the modified Hagen-Poiseuille equation was developed to i) assess the pressure induced by the grout at any installed depth, and ii) illustrate the importance of maintaining a proper amount of return flow to avoid build-up of excessive pressures in the ground during the jet grouting process. Combining the analytical and the finite element (FE) simulations, jet grouting induced soil displacements were determined. For flat terrain, the area affected by jet grouting was approximately three to four times the column radius. By contrast, for the studied slope (inclination of 1:3), the influenced area increased to about 10 times the column radius. The influenced area could increase further for steeper slopes. The obtained displacement magnitude was also considerably larger for sloping terrain than for flat terrain. The reported findings relate to jet-grouting in marine clays (which is not the normal application of this technology) and cannot be extrapolated to other soils.

Analysis of the stability of a novel assembled working shaft support structure during pipe jacking construction: Experiments and numerical simulations

Pipe jacking construction is a commonly employed trenchless technique for laying underground pipes in urban areas. However, the conventional support structure for pipe jacking shafts poses challenges, including difficulty in reserving pipe jacking holes, susceptibility to tilting, low bearing capacity, and the potential for failure during construction. Taking the 5# pipe jacking shaft of the pipe jacking construction for diverting the Yellow River through the river at Niukouyu in Zhengzhou City as the research background, investigates the soil settle deformation around the working shaft and the mechanical response law of the supporting structure during the short-distance, long-distance and second long-distance pipe jacking construction by combining the practical engineering field test and finite element numerical simulation, and carries out a sensitivity analysis on the main design parameters affecting the stability of the supporting structure through orthogonal test. The findings reveal that during the second pipe jacking construction, stress and deformation of the supporting structure are higher than those observed in the first pipe jacking. Notably, support piles and waist beams at the entrance of the pipe jacking experience greater force, and the back and side walls undergo increased force and deformation in the later stages of pipe jacking, and support pile spacing is the main control factor affecting the mechanical performance of the novel support structure. The study concludes that monitoring and protection measures should be reinforced, particularly in areas prone to failure and damage during construction. The insights gained from this research can serve as a reference for designing, optimizing, and safely monitoring novel assembled pipe jacking shaft support structures.

Rate-dependent energy dissipation of graded viscoelastic structures fabricated by grayscale vat photopolymerization

A major benefit of additive manufacturing technologies is precise control over structural topologies and material properties, which allows to tailor, for instance, energy absorption and dissipation. While vat photopolymerization is generally restricted to a single material, grayscale masked stereolithography (gMSLA) allows to customize material behavior by grading the light intensity within a structure. This study investigates the impact and opportunities of grayscale grading strategies on the rate-dependent mechanical behavior of structures fabricated by gMSLA. Considering the viscoelastic nature of polymers, rate-dependent energy dissipation is explored, introducing a parametric linear viscoelastic constitutive model for varying grayscales. The investigation includes the comprehensive characterization of mechanical properties, numerical finite element simulation, validation through experimental procedures, and exploration of dissipation energy under different strain rates. In this way, a rational function successfully determines the critical strain rate at which the maximum dissipation occurs. Overall, the research offers a comprehensive investigation of the mechanical dissipation behavior of graded 3D printed structures, laying the foundation for further studies and advancements aimed at optimizing these structures for enhanced energy absorption capabilities.

Multi-parameter terahertz metamaterial sensors based on single-layer quarter ring patterns

A terahertz metamaterial sensor based on a single-layer quarter ring pattern is proposed to realize the simultaneous measurement of temperature, refractive index, and other parameters through a metasurface consisting of a patterned quarter ring gold layer and a silicon substrate. Field finite element numerical simulations were performed to analyse the transmission and reflection spectra. A two-parameter sensor combined with electric field distribution was realized using multiple peaks, thus revealing the physical mechanisms of the interaction in metamaterial structures. In addition, the effect of each geometrical parameter on the sensor performance is also simultaneously analysed to verify the optimal selection of structural parameters. On this basis, the sensors are theoretically analysed at different incidence and polarization angles, and the results show that the transmittance is not sensitive to the polarization angle. The simulation results show that the transmittance at the resonant frequencies of 0.48 THz, 0.64 THz, 0.79 THz and 1.04 THz are 93.7 %, 79.1 %, 38.4 % and 50.8 %, respectively, and the refractive index sensitivities at the resonant frequencies are 6.84 GHz/RIU, 7.42 GHz/RIU, 8.22 GHz/RIU and 32.11 GHz/RIU, and quality factor Q of 6.76, 9.63, 15.51 and 26.28, respectively. The devices proposed in this study are simple in structure, easy to fabricate, easy to miniaturize and can be integrated for sensitivity, multi-parameter sensors. They can be functionally designed for chemical and biological sensing and other important applications.

Numerical Simulation and Deformation Prediction of Deep Pit Based on PSO-BP Neural Network Inversion of Soil Parameters

The finite element numerical simulation results of deep pit deformation are greatly influenced by soil layer parameters, which are crucial in determining the accuracy of deformation prediction results. This study employs the orthogonal experimental design to determine the combinations of various soil layer parameters in deep pits. Displacement values at specific measurement points were calculated using PLAXIS 3D under these varying parameter combinations to generate training samples. The nonlinear mapping ability of the Back Propagation (BP) neural network and Particle Swarm Optimization (PSO) were used for sample global optimization. Combining these with actual onsite measurements, we inversely calculate soil layer parameter values to update the input parameters for PLAXIS 3D. This allows us to conduct dynamic deformation prediction studies throughout the entire excavation process of deep pits. The results indicate that the use of the PSO-BP neural network for inverting soil layer parameters effectively enhances the convergence speed of the BP neural network model and avoids the issue of easily falling into local optimal solutions. The use of PLAXIS 3D to simulate the excavation process of the pit accurately reflects the dynamic changes in the displacement of the retaining structure, and the numerical simulation results show good agreement with the measured values. By updating the model parameters in real-time and calculating the pile displacement under different working conditions, the absolute errors between the measured and simulated values of pile top vertical displacement and pile body maximum horizontal displacement can be effectively reduced. This suggests that inverting soil layer parameters using measured values from working conditions is a feasible method for dynamically predicting the excavation process of the pit. The research results have some reference value for the selection of soil layer parameters in similar areas.

Seepage process understanding at long-existing landslide dams through numerical analysis and hydrological measurements

Landslide dams consist of unconsolidated heterogeneous material and lack engineering measures to drain water and control pore water pressure. They may be porous and seepage through them could potentially lead to piping failure. In this research, the internal processes within a long-existing landslide dam are assessed under transient seepage force. The implemented approach includes a 3D finite element numerical simulation executing fully coupled flow-deformation and consolidation methods based on hydraulic data measurements and geotechnical laboratory tests. The nonlinear constitutive model ‘Hardening Soil’ is applied to accurately calculate the stress-induced pore water pressure, effective stress, deformation, and flow. Further, the possibility of slope failure due to seepage force is investigated through the strength reduction method. The results highlight the dependency of the seepage flow on the corresponding variation of the relative permeability and saturation in the soil mediums under different rates of seepage force. Small rates of seepage force, however, impose deformation at the dam's crown. High effective stress is obtained at negative small rates of seepage force where the long duration of fluctuation is modeled. In the drawdown simulation, there is a reverse relation between effective stress and the rate of the seepage force. Through the modeling process and based on the measured data, two seepage paths are detected within the landslide dam, while their activation depends on the lake level. The modeling approach and the required data analysis are suggested for utilization in further studies regarding the seepage process understanding at the long-existing landslide dams and their hazard assessments in addition to the common geomorphological approaches.

Study on the Ionic Transport Properties of 3D Printed Concrete

Three-dimensional printed concrete (3DPC) is an anisotropic heterogeneous material composed of a concrete matrix and the interfaces between layers and filaments that form during printing. The overall ion transport properties can be characterized by the equivalent diffusion coefficient. This paper first establishes a theoretical model to calculate the equivalent diffusion coefficient of 3DPC. Verification through numerical calculations shows that this theoretical model is highly precise. Based on this, the model was used to analyze the effects of dimensionless interface parameters on the equivalent diffusion coefficients in different directions of 3DPC. Finally, the dynamic ionic transport properties of 3DPC were investigated through finite element numerical simulation. The results of the dynamic study indicate that interfaces have a significant impact on the ion distribution and its evolution within 3DPC. The product of the interface diffusion coefficient and interface size can represent the ionic transport capacity of an interface. The stronger the ionic transport capacity of an interface, the higher the ion concentration at that interface. Due to the “drainage” effect of lateral interfaces, the ion concentration in the middle of 3DPC with a smaller equivalent diffusion coefficient is higher than that in 3DPC with a larger equivalent diffusion coefficient.

Study on load-bearing behaviors of prestressed post-grouting tubular piles in the karst region of northern Fujian Province, China

The karst that is dominated by medium-weathered limestone and caves with various spatial features is widely distributed in the northern Fujian Province. This paper discusses the load-bearing behaviors of post-grouting tubular piles in karst region of north Fujian Province with reference to the prestressed tubular piles adopted in the residential buildings of Haixi Comprehensive Trade City Phase II Project in Sanming City. The load-settlement curve, pile side friction resistance, and pile end resistance of tubular piles are analyzed by finite element numerical simulations and field static load tests. The load-bearing behaviors of prestressed tubular piles under karst geological conditions with two different spatial features are comparatively investigated, and the effectiveness of tubular pile reinforcement is verified by field settlement observation. The results reveal that the finite element numerical model can effectively simulate the tubular pile-soil interaction. The use of pile end post-grouting of prestressed tubular piles in the karst region can significantly increase their load-bearing capacities. The top settlements of grouted tubular piles under the maximum test load can be reduced by 16.8%–22.3% compared with these of ungrouted test piles, and the theoretical simulated ultimate load-bearing capacity can be increased by 27.3%. The adoption of pile end post-grouting technique can reduce the pile end displacement of tubular piles and improve the proportion of pile end resistance. Plastic-hard plastic breccia silty clay can be used as a bearing stratum for post-grouting to achieve excellent grouting performance. The bead-shaped karst caves are more unfavorable to the exertion of load-bearing capacity of the tubular piles than the karst caves filled with plastic-hard plastic breccia silty clay to which the piles have direct access. The field monitored average settlements of the 19# and 17# buildings under karst geological conditions with two different spatial features are −12.88 mm and −8.98 mm, respectively, both of which do not exceed the warning value, indicating that it is feasible for the project to adopt the pile end post-grouting technique of the tubular piles. The achievements of this study help to further reveal the load-bearing mechanism of this type of pile, which can provide a basis for its engineering design and construction optimization.

Seismic performance verification and theoretical stiffness calculation for a novel assembled concrete dry-connected beam-column node

This paper proposes a novel assembled concrete dry-connected beam-column node, which consists of a precast concrete beam with steel haunch plates at the end and a precast concrete column connected by ordinary strength long bolts. The quasi-static test study and finite element numerical simulation of the node are used to analyze the hysteresis curve, skeleton curve, and other performance indexes and investigate mechanical properties under low-cycle reciprocating load. The results demonstrate that the overall stress performance of the column specimen is outstanding; the specimen node possesses large deformation and good ductility, presenting semi-rigid characteristics; the damage of the specimen mainly includes the bending deformation of the connecting bolts. By analyzing the damage and force mechanisms of the node, an "equivalence method" for the initial rotational stiffness calculation of the beam-column combination node is established. Moreover, the formula for calculating the stiffness of this semi-rigid node is deduced.

Coupling of Electric and Flow Fields to Enhance Ion Transport for Energy-Efficient Electrochemical Tap-Water Softening.

Electrochemical-induced precipitation is a sustainable approach for tap-water softening, but the hardness removal performance and energy efficiency are vastly limited by the ultraslow ion transport and the superlow local HCO3-/Ca2+ ratio compared to the industrial scenarios. To tackle the challenges, we herein report an energy-efficient electrochemical tap-water softening strategy by utilizing an integrated cathode-anode-cathode (CAC) reactor in which the direction of the electric field is reversed to that of the flow field in the upstream cell, while the same in the downstream cell. As a result, the transport of ions, especially HCO3-, is significantly accelerated in the downstream cell under a flow field. The local HCO3-/Ca2+ ratio is increased by 1.5 times, as revealed by the finite element numerical simulation and in situ imaging. In addition, a continuous flow electrochemical system with an integrated CAC reactor is operated for 240 h to soften tap water. Experiments show that a much lower cell voltage (9.24 V decreased) and energy consumption (28% decreased) are obtained. The proposed ion-transport enhancement strategy by coupled electric and flow fields provides a new perspective on developing electrochemical technologies to meet the flexible and economic demand for tap-water softening.

Excavation Effects on Reinforced Concrete Pile Foundations: A Numerical Analysis

The intricacies of foundation pit engineering often result in alterations to the surrounding environment, posing potential threats to the safe operation of nearby buildings and pile foundations. This study employs finite element numerical simulation to scrutinize the influence of vacuum preloading pressure, preloading duration, excavation slope ratio, excavation duration, and retaining pile wall depth on the stress and deformation of existing plain concrete pile foundations. The findings reveal that the impacts of excavation are primarily absorbed by both proximal and distal piles in relation to the pit. Moreover, elevating vacuum preloading pressure and extending the preloading duration during dewatering can lead to increased internal forces and displacement of the piles. Changes in excavation slope ratio exhibit minimal effects, while prolonged excavation duration can shift internal forces from predominantly positive to negative, with negligible impact on horizontal displacement. Importantly, augmenting the depth of the retaining pile wall embedding effectively mitigates the effects of pit excavation.

Numerical and experimental assessment of tilted-helical fiber orientation effects on deformation of pneumatic soft actuators

Pneumatic actuation of fiber-reinforced soft-material slender structures, and specifically inflatable cylinders, plays a key role in soft robotics, particularly for generating sought deformations in terms of, e.g. elongation, expansion, torsion, and bending. Fiber-reinforced tubes were widely investigated, in particular by considering regular helical patterns for the fibers, and multiple sets of fibers were introduced for achieving relatively richer deformations such as coiling (i.e. combined bending and torsion). However, coiling can be obtained even by introducing a single tilted-helical fiber, thus potentially simplifying actuator design and implementation. Therefore, in this study, we numerically investigated the effect of fiber orientation on the coiling behavior of tilted-helical fiber-reinforced cylindrical actuators. Specifically, we used finite element numerical simulations to determine the effect of fiber pitch and tilt angle on the curvature and twist angle of an inflated cylindrical actuator, and we assessed numerical results based on corresponding experiments. Finally, we addressed a preliminary design chart based on the inverse map linking coiling to the corresponding pitch and tilt angle. Our results take an initial step for the design of tilted-helical fiber-reinforced actuators, with potential application to a wider class of inflatable soft actuators to program a desired coiled configuration through the integration of a single tilted-helical fiber.

Investigation into hydrogen induced fracture of cable bolts under deep stress corrosion coupling conditions

The coupling effects of geostress and multi-attribute corrosion environments are the major causes of damage and rupture of prestressed cable bolts in deep underground environments. To determine impacts of different environmental factors on stress corrosion cracking of cable bolts in underground conditions, the accelerated stress corrosion tests and finite element numerical simulations were carried out. By implementing the material diffusion theory and appreciating the hydrogen induced lattice expansion effects, the diffusion and aggregation behavior of hydrogen in cable bolts were simulated. The influences of stress intensity and hydrogen concentration on failure mechanisms of cable bolts were studied by considering the hydrogen induced expansion strain. The failure only occurred in the environments where sufficient hydrogen concentration existed. The hydrogen diffusion flux and distribution were consistent with stress concentration distribution. The prestress accelerated the hydrogen diffusion to stress concentrated position leading to a greater strain in the stressed areas, which consequently induced hydrogen expansion stress and decreased cohesion strength of lattice near crack tip. The fractographic features of failed specimen were analysed and hydrogen assisted fracture was confirmed to be one of the main failure mechanisms leading to stress corrosion failures. The methodologies proposed could be used to study the diffusion and distribution of hydrogen in metals and the obtained results improved the understanding failure mechanism of hydrogen assisted SCC.

Constitutive model of MWCNTs/PDMS composites considering volume change and electromechanical response characteristics under impact load

Multi-walled carbon nanotubes/polydimethylsiloxane (MWCNTs/PDMS) composites have excellent electromechanical conversion ability which can be applied in the field of intelligent sensing. However, the volume changes and electromechanical response mechanism of MWCNTs/PDMS under dynamic load remain unclear. In this paper, the electromechanical response of MWCNTs/PDMS with different mass ratio of MWCNTs are studied by quasi-static compression, SHPB experiment and finite element numerical simulation. The quasi-static compression results show that volume ratios of MWCNTs/PDMS are decreased with compression strain (0.845 when strain is 0.5), then, the Yeoh hyperelastic constitutive model is established considering volume change. When the mass ratio of MWCNTs is 1 wt%, MWCNTs/PDMS shows the best mechanical properties. The stationary phases of strain rate of MWCNTs/PDMS decrease with increasing of impact velocity, showing obvious viscoelastic mechanical properties. The impact induced voltages of MWCNTs/PDMS are generally larger than PDMS (10∼15 m/s). The flexoelectric effect of MWCNTs/PDMS under impact is further studied based on numerical simulations. The results show that the strain gradients are within 10−2∼10−1 m−1, the related flexoelectric coefficients are within 10−10–10−9 C/m. In summary, this study can further expand the application of MWCNTs/PDMS in the field of intelligent sensing.

Influence of Core Wall Type on Crack Resistance of Core Wall

The hydraulic fracturing resistance of asphalt concrete core wall mainly depends on physical and mechanical factors such as the material of the core wall and the geometric size of the core wall. Three types of core wall types, such as equal thickness type, gradient type and stepped type, are often used in practical engineering. In order to study the influence of core wall types on the cracking resistance of the core wall, Duncan Zhang E-B model is used to conduct finite element numerical simulation of five different core wall types. By analyzing the stress deformation of the center wall of different schemes, it is concluded that the equal thickness core wall has the best anti-hydraulic splitting performance without considering the engineering cost.

Mechanical characteristics and application of cement-soil wrapped pile support structures for soil-rock combination pit in coastal area

In order to explore the mechanical properties of cement-soil wrapped pile support system in soil-rock combination foundation pit support. In this paper, based on a deep foundation pit project in Qingdao, the horizontal displacement monitoring test of cement-soil wrapped pile support system was carried out. Combined with ABAQUS finite element numerical simulation, the foundation support model of cement-soil wrapped pile in soil-rock combination foundation was established. The variation rule of bending moment and displacement of cement-soil wrapped pile under different influencing factors is explored, And the reasonable position of the micro steel pipe piles in the cement-soil pile is clarified. The results of the study show that the micro steel pipe piles have the best support with less horizontal displacement when they are located on the excavation side of the foundation pit. With the gradual increase of excavation depth, the horizontal stress of the soil basically increases linearly, which is consistent with the change rule of active soil pressure along the depth direction. Increasing the strength of cement-soil can significantly improve the deformation resistance of the supporting structure. The research results can provide reference for the design and construction of foundation support for soil-rock combination foundations.

Feasibility study of TSOB replacing standard high-strength bolt in T-stub connection

The feasibility study of T-head Square-neck One-side Bolt (TSOB) replacing Standard High-strength Bolt (SHB) in T-stub connections is conducted in this paper. Parametric analysis is carried out by means of finite element numerical simulation to reveal the effects of T-stub parameters and bolt parameters on the tensile performance of T-stub connections using SHBs and TSOBs. The plastic hinge theory is applied to explain the mechanism for the difference formation in tensile capacity between the two types of connections. The results show that the failure modes of TSOBs bolted T-stubs are the same as those of SHBs bolted T-stubs, including complete flange yielding, bolt failure with flange yielding, and bolt failure. For the failure of complete flange yielding, the tensile capacity of TSOBs bolted T-stubs is reduced by 7.2%∼16.4% compared with that of SHBs bolted T-stubs, whereas the modes of bolt failure with flange yielding and bolt failure do not cause a difference between the two types of connections in tensile response. Two modifications on design equation and design result by introducing hole type reduction factor and thickening flange for T-stub connections were proposed, respectively. The modified design methods can be used in the design of TSOBs bolted T-stubs and are identical to the design criteria of specifications Eurocode 3 and P398 for SHBs bolted T-stubs. Besides, the high-strength large hexagon nuts for steel structures and assembly classes of H12 and H13 recommended by GB/T 1229–2006 and GB/T 5277–1985 should be preferred for TSOBs bolted T-stubs. Moreover, horizontal slotted bolt holes are recommended for practical constructions, and the T-head aspect ratio of TSOB in the range of 1.6–2.0 does not affect T-stub tensile performance.